North Stand Construction Discussion

[johnny crossan]

Thanks.

there's a lot of single handed stand brushing going on in the last video though!

 

[Coatigan]

View attachment 162742

Looks like the infil piece where the temporary (pivoting) bracing was fixed through. I assumed those metal coverings were protective and would all go but maybe they will stay, and this is the additional bit to plugh the hole, rather than casting a concrete piece. In which case, he could be applying an anti slip coating.

 

[SouthStandStander]

View attachment 162742

Clearly putting some sort of sealent in the gaps. That brush is adequate and the right rhing to use to move dust away before the sealent.
Stand down JRB. No human rights abuses occurring here.

 

[jrb]

Clearly putting some sort of sealent in the gaps. That brush is adequate and the right rhing to use to move dust away before the sealent.
Stand down JRB. No human rights abuses occurring here.

Yeah, jumped the gun on this one.

He's doing a great job. :-)

 

[Centurions]

That proves the roof is wonky.

The apex is where the 5th bay from the left meets the 6th bay from the right.

The 6th bay from either side (middle bay) should be horizontal and it definitely isn't.

If there is a problem could it not be perhaps due to an imbalance in load from the stored items up there?

 

[bluekeith]

I am hoping the drone boy's can capture the yellow support's being removed, they look like they have tracks to pull them back then lift off. The engineering on the development has been top notch.

 

[Centurions]

I am hoping the drone boy's can capture the yellow support's being removed, they look like they have tracks to pull them back then lift off. The engineering on the development has been top notch.

The supports under the quod pods? I think the horizontal beams at the bottom are just load spreaders. Maybe.

 

[mcfcphil]

Clearly putting some sort of sealent in the gaps. That brush is adequate and the right rhing to use to move dust away before the sealent.
Stand down JRB. No human rights abuses occurring here.

Delaney will be penning an article quoting Amnesty if we’re not careful

 

[blueparrot]

Clearly putting some sort of sealent in the gaps. That brush is adequate and the right rhing to use to move dust away before the sealent.
Stand down JRB. No human rights abuses occurring here.

Good news, almost a blueparrot brings work to a standstill with mildly humourous post situation.:)

 

[bluekeith]

The supports under the quod pods? I think the horizontal beams at the bottom are just load spreaders. Maybe.

They are the one's. With some of the innovative solutions they have used I hope they are both load spreaders and rails to pull it backwards.

 

[johnny crossan]

Delaney will be penning an article quoting Amnesty if we’re not careful

He'll have a mole counting how many times the First Aid box has been opened.

 

[Lost for words]

I think there is an element of truth to it, and those that have pointed it out aren't being daft.

The photos from the air at an angle make it worse than it maybe is, combined with the netting draping more over one side than the other, the curve against the straight creates a bit of a depth discrepancy.

Looking at it from the pitchside, the image a page or two back, it looks far more even. But even then, you can see it in the protective railing on top, which should be paralel. There is a dip in it at that eastern middle beam, which does suggest one of the two is either too high or top low.

Lots of time left in the build, but at this point more likely to be a packer job than any adjusting, as previously commented.

 

[Leetwilliams]

For all of the flack I was given for pointing that out about the roof, I’ll take that apology now…LOL

 

[Leveblue]

I see what you mean - but is it the temporary bits that make it seem out of kilter?

View attachment 162748

I think the drone needs to be plumb center to get a true image. I reckon it it was plumb center it would look okay. Any deviation left or right of true center gives a misleading image. We'll just have to wait and see when its finished.

 

[eyalluvitt]

I see what you mean - but is it the temporary bits that make it seem out of kilter?

View attachment 162748

Sisk’s last big job, in Italy apparently

 

[Leeky]

If there is a problem could it not be perhaps due to an imbalance in load from the stored items up there?

View attachment 162755

Plus factor in the weight of the structural piece to go on top for the Sky walk which will surely align all pieces as they will need to connect to different trusses

 

[failsworthblueboy]

Couple of pics from today

 

[failsworthblueboy]

Sorry for the poor quality the beautiful sunshine played havoc.

 

[bluekeith]

Couple of pics from today

I thought for a minute in photo 2 they had put the side cap on until I noticed it was a street light.

 

[eyalluvitt]

Best hole filler in the business, bar none